Author : Adiscon Support

===============================

CVE: CVE-2014-3634

Status of this report
———————
FINAL

Reporter
——-
Rainer Gerhards, rsyslog project lead

Affected
——–
– rsyslog, most probably all versions (checked 5.8.6+)
– sysklogd (checked most recent versions)
– potentially others (see root cause)

Root Cause
———-
Note: rsyslogd was forked from sysklogd, and the root cause applies to
both. For simplicity, here I use sysklogd as this is the base code.

The system header file /usr/include/*/syslog.h contains the following definitions

#define    LOG_NFACILITIES    24    /* current number of facilities */
#define    LOG_FACMASK    0x03f8    /* mask to extract facility part */
/* facility of pri */
#define    LOG_FAC(p)    (((p) & LOG_FACMASK) >> 3)

[This is from Ubuntu 12.04LTS, but can be found similarly in most, if
not all, distributions].

The define LOG_NFACILITIES is used by sysklogd to size arrays for facility
processing. In sysklogd, an array for selector matching is using this. Rsyslog
has additional array. The macro LOG_FAC() is used to extract the facility from
a syslog PRI [RFC3164, RFC 5424]. Its result is used to address the arrays.
Unfortunately, the LOG_FACMASK permits PRI values up to 0x3f8 (1016 dec). This
translates to 128 facilities. Consequently, for PRI values above 191 the
LOG_NFACILITIES arrays are overrun.

Other applications may have similar problems, as LOG_NFACILITES “sounds” like
the max value that LOG_FAC() can return. It would probably make sense to
check why there is a difference between LOG_NFACILITES and LOG_FACMASK, and
if this really needs to stay. A proper fix would probably be to make LOG_FAC
return a valid (maybe special) facility if an invalid one is provided. This
is the route taken in rsyslog patches.

Effect in Practice
——————

General
~~~~~~~
Almost all distributions do ship rsyslog without remote reception by
default and almost all distros also put firewall rules into place that
prevent reception of syslog messages from remote hosts (even if rsyslog
would be listening). With these defaults, it is impossible to trigger
the vulnerability in v7 and v8. Older versions may still be vulnerable
if a malicious user writes to the local log socket.

Even when configured to receive remote message (on a central server),
it is good practice to protect such syslog servers to accept only
messages from trusted peers, e.g. within the relay chain. If setup in
such a way, a trusted peer must be compromised to send malfromed
messages. This further limits the magnitude of the vulnerability.

If, however, any system is permitted to send data unconditionally to
the syslogd, a remote attack is possible.

sysklogd
~~~~~~~~
Sysklogd is mildly affected. Having a quick look at the current git master
branch, the wrong action may be applied to messages with invalid facility.

A segfault seems unlikely, as the maximum misadressing is 104 bytes of the
f_pmask table, which is always within properly allocated memory (albeit to
wrong data items). This can lead to triggering invalid selector lines and
thus wrongly writing to files or wrongly forwarding to other hosts.

rsyslogd
~~~~~~~~
Rsyslogd experiences the same problem as sysklogd.

However, more severe effects can occur, BUT NOT WITH THE DEFAULT CONFIGURATION.
The most likely and thus important attack is a remote DoS. Some
of the additional tables are writable and can cause considerable misadressing.
This is especially true for versions 7 and 8. In those versions, remote code
injection may also be possible by a carefully crafted package. It sounds hard
to do, but it cannot be totally outruled [we did not check this in depth].

A segfault (and thus Dos) has the following preconditions:
– the rsyslog property “pri-text” must be used, either in
* templates
* conditional statements (RainerScript and property-based filters)
– the property must actually be accessed
With traditional selector lines, this depends on the facility causing
a misadressing that leads to reading a 1 from the misaccessed location.

When the preconditions are met, misadressing happens. The code uses a string
table and a table of string lengths. Depending on memory layout at time of
misadressing and depending on the actual invalid PRI value, the lookup to
the string table can lead to a much to long length, which is the used in
buffer copy calculations. High PRI values close to the max of 1016 potentially
cause most problems, but we have also seen segfaults with very low invalid
PRI values.

Note that, as usual in such situations, a segfault may not happen immediately.
Instad some data structures may be damaged (e.g. from the memory allocator)
which will later on result in a segfault.

In v5 and below, a segfault is very unlikely, as snprintf() is used to generate
the pri-text property. As such, no write overrun can happen (but still garbagge
be contained inside the property). A segfault could theoretically happen if the
name lookup table indices cause out-of-process misadressing. We could not manage
to produce a segfault with v5.

Versions 7.6.3 and 7.6.4 already have partial fixes for the issue and will not
be vulnerable to a segfault (but the mild other issues described).

All other versions 7 and 8 are vulnerable. Version 6 was not checked as it seems
no longer be used in practice (it was an interim version). No patch for version 6
will be provided.

Note that a segfault of rsyslog can cause message loss. There are multiple
scenarios for this, but likely ones are:

– reception via UDP, where all messages arriving during downtime are lost
– corruption of disk queue structures, which can lead to loss of all disk
queue contents (manual recovery is possible).

This list does not try to be complete. Note that disk queue corruption is likely
to occur in default settings, because the important queue information file (.qi)
is only written on successful shutdown. Without a valid .qi file, queue message
files cannot be processed.

How to Exploit
————–
A syslog message with an invalid PRI value needs to be sent. It is sufficient
to send just the PRI as in this example

“<201>”

Any message starting with “<PRI>” where PRI is an integer greater than 191
can trigger the problem. The maximum offset that can be generated is with
PRI equal to 1016, as this is the modulus used due to LOG_FACMASK.

Note that messages with
– PRI > 191  and
– PRI modulus 1016 <= 191
will not lead to misadressing but go into the wrong bin.

Messsages with
– PRI > 191
– PRI modulus 1016 > 191
will go into the wrong bin and lead to misadressing.

Severity
——–
Given the triggering scenarios, the fact that multiple changes must be made to
default system configurations and potential problems we classify the severity
of this vulnerability as

MEDIUM

Note that the probability of a successful attack is LOW. However, the risk of
message loss is HIGH in those rare instances where an attack is successful. As
mentioned above, it cannot totally be outruled that remote code injection is
possible using this vulnerability.

This vulnerability is at least not publicly know. Based on (no) bug reports, it
seems unlikely that it is being exploited, but that’s obviously hard to know for
sure.

Patches
——-
Patches are available for versions known to be in wide-spread use.

Version 8.4.1 is not vulnerable. Version 7.6.6, while no longer being project
supported received a patch and is also not vulnerable.

New patches for the article available http://www.rsyslog.com/remote-syslog-pri-vulnerability-cve-2014-3683/